Lone Star Jeep Club http://www.lsjc.org/board/ A forum for members of the Lone Star Jeep Club, or any other four-wheeling enthusist. en Fri, 18 May 2012 00:56:13 GMT vBulletin 60 http://www.lsjc.org/board/images/SeamusLight/misc/rss.png Lone Star Jeep Club http://www.lsjc.org/board/ Drives Shafts 2012 JK http://www.lsjc.org/board/showthread.php?61047-Drives-Shafts-2012-JK&goto=newpost Thu, 17 May 2012 22:40:43 GMT Had my new drive shafts from Tom Wood's installed today on my 2012 Rubi - Josh over at Baertrax took great care of me!
Since I lifted my 2dr 2012 I needed new shafts for clearance and strength reasons. With the new shafts
I gained massive clearance between the front shaft and X over pipe and I didn't have to install ANY exhaust spacers and I got rid of the sealed boots. (the OEM sealed boots on the shafts would have self-destructed the first time off road
with my 3.5" lift) I did a 1310 in the front and 1350 in the rear.

Yummy tasty goodness - new shafts front and rear:


OEM front shaft and X over pipe for the front shaft - very tight and no way can I do full drop on suspension.


Here is the new clearance with the new front 1310 shaft between the X over pipe:
(might have to remove that heat shield - don't think I need that any more since no more rubber boot right there.)


Another view of the front shaft (looking forward):


Detail front shaft:


Rear OEM shaft:


New rear shaft big and beefy:


Like to get this on some RTI ramps and double check everything.... ]]> Projects Cosmos http://www.lsjc.org/board/showthread.php?61047-Drives-Shafts-2012-JK 1996 XJ for parts. Rigid bumper http://www.lsjc.org/board/showthread.php?61046-1996-XJ-for-parts-Rigid-bumper&goto=newpost Thu, 17 May 2012 22:12:48 GMT OK guys! I have a 1996 XJ that I need to sell for parts. I'm asking $600. It has about 200k. The 4.0 apparently blew a head gasket and filled the oil with water. My son drove it several days like that, and now it sounds horrible, and smokes a lot. It will crank and move, but is not driveable.
The good: it has a Rigid front bumper with hoop, and receiver. Rigidco.com ($450 new). Zone offroad 3" lift with AAL. (about 3 years old, shocks may be shot). Chrysler 8.25 rear, and Dana HP30 with 3.55 gears. NP 231, and AX4. Tcase and transmission are fine. No problems with axles. Rear was replaced from a wrecking yard last summer. Old housing is included, but pinion bearing and seal are out.
In the past year, I have replaced the starter, hard transmission lines, distributor, CPS. The radiator is fairly new also. I has 2 31x10.50 Goodyear Authority tires that are very good. (about a year old) The other 3 are bald. All power windows work, all doors close well. (the back handles are hard to push) It has been wheeled a lot, but not very extreme. The brakes are fairly new, (drums and rotors were replaced, along with pads and shoes) Recent water pump. Torque converter replaced about 2 years ago. Absolutely no rust of any kind. All glass is good, tinted windows. The dash is in good shape. Cruise works. All lights work. Factory trailer hitch in the rear. header panel is good, and aftermarket grill is OK.

The bad: most of the body is dented and or dinged somewhere. Except the hood, and drivers door. Back hatch is cracked, but another one in good condition is included. The headliner is gone, the seats are dirty, but no holes or tears. The carpet is filthy. It has the stock alloy wheels which have been rattle canned black. The original black paint was peeling, and most of the body has been rattle canned as well. Hood latch cable is broken. Original sway bar and skid plate are off, but included. Steering gear box is worn out. (pops and crunches when turning) A/C doesn't cool. (I think the compressor is bad, but it does turn on) No radio. The tail lights and front marker lenses have been blacked out, and won't pass inspection. The motor difinately needs rebuilding or replacing, don't expect it to be driveable.

I'm trying to get pics on here, but I have some on my phone. I can send them. If you're interested call 903 245-3262, or text for pics. I'm in Tyler, and the Jeep will need to be towed or trailered. If I don't answer, leave a message, and I'll get back to you. ]]> JEEPS For Sale spdcat http://www.lsjc.org/board/showthread.php?61046-1996-XJ-for-parts-Rigid-bumper TJ 5 speed shift knob http://www.lsjc.org/board/showthread.php?61045-TJ-5-speed-shift-knob&goto=newpost Thu, 17 May 2012 22:12:38 GMT Need a 97-04 TJ shift knob 5 speed Need a 97-04 TJ shift knob 5 speed ]]> Want Ads High Hefner http://www.lsjc.org/board/showthread.php?61045-TJ-5-speed-shift-knob T176 and Dana 300 clocked and twin sticked http://www.lsjc.org/board/showthread.php?61044-T176-and-Dana-300-clocked-and-twin-sticked&goto=newpost Thu, 17 May 2012 22:06:24 GMT My brother has a T176 we bought and planned to use to replace his T5. We had the shift forks replaced and replaced the rear seal. Also have a seal... My brother has a T176 we bought and planned to use to replace his T5. We had the shift forks replaced and replaced the rear seal. Also have a seal spacer to make up for the clocking ring we had on our Dana 300. Planned to run it but decided to buy an Atlas before price increase and run our automatic we have. $500 obo

Also have a Dana 300 that is clocked and twin sticked. $450 obo

John
nine o 3 818 358 four
Attached Images
]]> Parts and Accesories For Sale scramblerj http://www.lsjc.org/board/showthread.php?61044-T176-and-Dana-300-clocked-and-twin-sticked Anybody going through tennessee anytime soon? http://www.lsjc.org/board/showthread.php?61043-Anybody-going-through-tennessee-anytime-soon&goto=newpost Thu, 17 May 2012 21:31:48 GMT Well I had a guy I work with that brought some of popcorn suttons Tennessee white whiskey back from vacation and I want some of my own!!!the down... Well I had a guy I work with that brought some of popcorn suttons Tennessee white whiskey back from vacation and I want some of my own!!!the down side is that they only sell it there so I figured I'd see if anybody was going that way anytime soon. Please let me know if you can help me out!!! ]]> Off-Topic Freak http://www.lsjc.org/board/showthread.php?61043-Anybody-going-through-tennessee-anytime-soon New Family from McKinney area http://www.lsjc.org/board/showthread.php?61042-New-Family-from-McKinney-area&goto=newpost Thu, 17 May 2012 21:01:06 GMT Hello all,

We attended the get together last night at Fuzzy's Tacos and had a blast meeting everyone. My wife, Autumn, is also registered here as user CoonAzz. My wife's Jeep is an Orange Crush 2012 JK Unlimited Sport, with a 6 speed manual. Its mainly stock except for upgraded to the 17 inch JK aluminum wheels, a 1 inch front spacer and Rubicon Rock Sliders. We have a ton of plans for additional parts and we hope to attend more of the meetings in the future.

Jake ]]> Introductions JakeNAutumn http://www.lsjc.org/board/showthread.php?61042-New-Family-from-McKinney-area chinese atv http://www.lsjc.org/board/showthread.php?61041-chinese-atv&goto=newpost Thu, 17 May 2012 20:50:29 GMT Anyone have one of the cheapos they want to unload. Wanting something small for my niece to ride. I found them new for about $900 for the nicer ones,... Anyone have one of the cheapos they want to unload. Wanting something small for my niece to ride. I found them new for about $900 for the nicer ones, might just go that route. ]]> Want Ads David Anderson http://www.lsjc.org/board/showthread.php?61041-chinese-atv Dana 44 Side and Spider Gears http://www.lsjc.org/board/showthread.php?61040-Dana-44-Side-and-Spider-Gears&goto=newpost Thu, 17 May 2012 20:23:10 GMT I have 2 sets of side and spider gears for a Dana 44 / 30 spline, shims too. I will give them to you for what I got them for...12 cold beverages. ... I have 2 sets of side and spider gears for a Dana 44 / 30 spline, shims too. I will give them to you for what I got them for...12 cold beverages.

An awesome LSJC memeber traded me, and unfortunately they do not fit my diff...(my rookie mistake) and if you need them I will make the same trade to you. ]]> Parts and Accesories For Sale DeRay http://www.lsjc.org/board/showthread.php?61040-Dana-44-Side-and-Spider-Gears DDR3 laptop ram http://www.lsjc.org/board/showthread.php?61039-DDR3-laptop-ram&goto=newpost Thu, 17 May 2012 19:58:45 GMT Used for laptops, netbooks, and SOME desktops. I have 3 gigs, a 2gb stick, and a 1 gb stick. 10600s. $10 :decision: Used for laptops, netbooks, and SOME desktops.

I have 3 gigs, a 2gb stick, and a 1 gb stick. 10600s.

$10

:decision: ]]> Miscellaneous For Sale David Anderson http://www.lsjc.org/board/showthread.php?61039-DDR3-laptop-ram Grote Trilliant http://www.lsjc.org/board/showthread.php?61035-Grote-Trilliant&goto=newpost Thu, 17 May 2012 19:21:24 GMT Hey do any of u guys k ow how to run a 24v system? I have 6 grote trilliant led light bars im not to shabby with electrical systems so if I can... Hey do any of u guys k ow how to run a 24v system? I have 6 grote trilliant led light bars im not to shabby with electrical systems so if I can figure them out in the next day or so they are going bye bye


http://m.summitracing.com/parts/GTE-63591. These are them for reference. I got them for $350 a piece used and if I can't get them to work ill sell them here for $200 a piece


I've been researching for hours but its looking to be more difficult then I originally anticipated. ]]> General Jeep Discussions 09taco http://www.lsjc.org/board/showthread.php?61035-Grote-Trilliant Hello Another new guy. http://www.lsjc.org/board/showthread.php?61034-Hello-Another-new-guy&goto=newpost Thu, 17 May 2012 19:10:48 GMT Hello, My name is Mike and I'm new to LSJC. I am trying to get my jeep back on the road. I'm from Texas but moved away to SC when I was 17. So me and my Jeep, which is a 1987 YJ with a 2" body lift and 32" tires have been through some SC swamp mud. I used to run circles around my friends w/out jeeps, but what do you expect its a jeep lol. I now live in the Denton area and ready to go toppless. ]]> Introductions Mdfiremedic73 http://www.lsjc.org/board/showthread.php?61034-Hello-Another-new-guy spacers vs axle narrowing http://www.lsjc.org/board/showthread.php?61032-spacers-vs-axle-narrowing&goto=newpost Thu, 17 May 2012 18:53:01 GMT I am looking to get some advice on spacers vs axle narrowing. After five and a half months, I finally got my Jeep YJ frame back from this "superb" shop in Dallas with Dana 60's under it. Problem is, what I GOT is not what I told them I WANTED. Seeing as it cost me over $12,000, I expected a lot better product. The axles I supplied were of different width and the front was SUPPOSED to be narrowed to either match or closely match the rear. The front is six and a half inches wider than the rear and now I am left with either using spacers, forking over MORE money (obviously to a DIFFERENT shop), or running it as is. Input on the issue would be greatly appreciated. I could also use some input on a decent fab and/or drivetrain shop. ]]> General Tech Topics biggun46 http://www.lsjc.org/board/showthread.php?61032-spacers-vs-axle-narrowing OAKLEY HD-Polarized TEN - Black Ink Frame / Red Iridium Lens http://www.lsjc.org/board/showthread.php?61031-OAKLEY-HD-Polarized-TEN-Black-Ink-Frame-Red-Iridium-Lens&goto=newpost Thu, 17 May 2012 18:41:44 GMT Oakley HD Polarized "Ten" Sunglasses - Ink Black Frames / 00 Red Iridium Polarized Lens

These Oakleys are new... I received them as a gift and worn them briefly on two occasions. I love the lenses, but decided this style frame was bigger than I prefer so I'm looking to sell these in order to buy a different pair. These glasses will come with everything... (glasses, oakley bag, orginal box, warranty papers...etc). I've even got the orignal shipping box that I'll mail them to you in.

As I said, I received these as a gift and they retail for $170... How 'bout $140 and I'll mail them to you at my expense...

Here's some pics... these glasses are flawless, guaranteed!

100_4526.jpg100_4528.jpg100_4542.jpg100_4546.jpg
Attached Images
]]> Miscellaneous For Sale ymerej71 http://www.lsjc.org/board/showthread.php?61031-OAKLEY-HD-Polarized-TEN-Black-Ink-Frame-Red-Iridium-Lens Warn Winch http://www.lsjc.org/board/showthread.php?61029-Warn-Winch&goto=newpost Thu, 17 May 2012 17:34:23 GMT Looking for a winch for my TJ. Anyone know the difference between the Warn M and VR winches? Looking for a winch for my TJ. Anyone know the difference between the Warn M and VR winches? ]]> General Jeep Discussions Texas Gringo 2 http://www.lsjc.org/board/showthread.php?61029-Warn-Winch 1991 Jeep Comanche http://www.lsjc.org/board/showthread.php?61028-1991-Jeep-Comanche&goto=newpost Thu, 17 May 2012 14:11:40 GMT ImageUploadedByTapatalk1337263253.830662.jpgI have a 1991 Jeep Comanche I have been restoring and am out of time & money!:( It is a 4.0l HO with a newly rebuilt AX15 and clutch. It's got 4:10 gears and a np231 transfer case. It was wrapped with camp clad this past fall. That was a $1000 alone. Truck runs and drives great with no known rust or problems. Mileage is unknown. I have repaired the speedometer so it works properly now. It is licensed and inspected. Floorboards are sprayed with a bed liner material. Any other questions just call thanks. I live between Tyler and Longview if you would like to see the truck. I20 exit 579. I've got $3200 on Craigslist asking price. I could probably take $3000. I've got a lot more than that in it though. 903 987 2337 Chris.
Attached Images
]]> JEEPS For Sale csschriver http://www.lsjc.org/board/showthread.php?61028-1991-Jeep-Comanche